ivasawajin
Member
i heard you have to clean them everyother month or when its gets dirty cuz they are nitrate magnets . how can i clean them without killing the bacteria on them ??
Cleaning BioBalls,Medias,Ceramics ?
- Thread starter ivasawajin
- Start date
2quills
Well-Known Member
[list type=decimal]
[*]
Place some new saltwater in a five gallon plastic bucket, or any other type of good sized deep plastic container. This is where you will rinse and clean the bio-balls off. If you are planning for a water change, water removed from the aquarium may be used for this as well.
[*]
Turn off the filter.
[*]
Remove about 1/4 of the bio-balls from the filter chamber and place them into the container with the saltwater.
[*]
Stir and swish the bio-balls around in the saltwater to break all the gunk or organic matter loose that is stuck on them. If they are extremely dirty, you may have to repeat this step. DO NOT scrub the bio-balls! Just allow the saltwater to do the job, nothing more than that.
[*]
Scoop the rinsed bio-balls out and place them back into the filter bio-chamber. A plastic kitchen colander works great for this, but any type of cup or small container with drain holes in it will do. The bio-balls come out, the yucky water stays behind.
[*]
Restart the filter.
Test for the appearance of ammonia every few days for a week, then every several days over another week after that. If the testss read near zero after this time, it is ok to repeat the process. If ammonia does appear, wait until readings drop back to zero, then wait another couple of weeks after that before repeating the process with the next batch of bio-balls.
Tips:
This procedure is suggested to be performed on aquariums that have been running for at least 4 months, because the nitrifying bacteria have had time to develop a strong population, and in all likelihood the bio-balls have begun to accumulate a substantial, but not overwhelming amount of DOCs (Dissolved Organic Compounds) on them.
NEVER use freshwater to clean the bio-balls, and NEVER clean all the bio-balls at once, as this in all likelihood WILL cause your system to crash! Because this procedure strips away and weakens the nitrifying bacteria population present on the bio-balls that the aquarium relies on to keep ammonia and nitrite in check, only clean about 1/4 of the bio-balls during any one cleaning session.
If your system has been running for sometime, say longer than 6 months, with no bio-ball maintenance at all, it may take a little time to get them cleaned up first. After that you can determine when periodic cleanings need to be performed based on how your individual system is set up and functions. You'll learn to know when it needs to be done.
Test for cleaning by lightly stirring up the top layer of the bio-balls. You will see gunk break loose. The only problem here is that in most all cases the mass of the organic matter settles in the bottom layer. You can stir the bio-balls up from the bottom, but be careful doing this because you may get a bunch of gunk shot into the tank if the filter output goes directly into the tank.
This procedure can be used to clean not only bio-balls, but other types of biological filtration mediums as well.
[/list type=decimal]
[*]
Place some new saltwater in a five gallon plastic bucket, or any other type of good sized deep plastic container. This is where you will rinse and clean the bio-balls off. If you are planning for a water change, water removed from the aquarium may be used for this as well.
[*]
Turn off the filter.
[*]
Remove about 1/4 of the bio-balls from the filter chamber and place them into the container with the saltwater.
[*]
Stir and swish the bio-balls around in the saltwater to break all the gunk or organic matter loose that is stuck on them. If they are extremely dirty, you may have to repeat this step. DO NOT scrub the bio-balls! Just allow the saltwater to do the job, nothing more than that.
[*]
Scoop the rinsed bio-balls out and place them back into the filter bio-chamber. A plastic kitchen colander works great for this, but any type of cup or small container with drain holes in it will do. The bio-balls come out, the yucky water stays behind.
[*]
Restart the filter.
Test for the appearance of ammonia every few days for a week, then every several days over another week after that. If the testss read near zero after this time, it is ok to repeat the process. If ammonia does appear, wait until readings drop back to zero, then wait another couple of weeks after that before repeating the process with the next batch of bio-balls.
Tips:
This procedure is suggested to be performed on aquariums that have been running for at least 4 months, because the nitrifying bacteria have had time to develop a strong population, and in all likelihood the bio-balls have begun to accumulate a substantial, but not overwhelming amount of DOCs (Dissolved Organic Compounds) on them.
NEVER use freshwater to clean the bio-balls, and NEVER clean all the bio-balls at once, as this in all likelihood WILL cause your system to crash! Because this procedure strips away and weakens the nitrifying bacteria population present on the bio-balls that the aquarium relies on to keep ammonia and nitrite in check, only clean about 1/4 of the bio-balls during any one cleaning session.
If your system has been running for sometime, say longer than 6 months, with no bio-ball maintenance at all, it may take a little time to get them cleaned up first. After that you can determine when periodic cleanings need to be performed based on how your individual system is set up and functions. You'll learn to know when it needs to be done.
Test for cleaning by lightly stirring up the top layer of the bio-balls. You will see gunk break loose. The only problem here is that in most all cases the mass of the organic matter settles in the bottom layer. You can stir the bio-balls up from the bottom, but be careful doing this because you may get a bunch of gunk shot into the tank if the filter output goes directly into the tank.
This procedure can be used to clean not only bio-balls, but other types of biological filtration mediums as well.
[/list type=decimal]
spanko
Active Member
Nice job Quills. Would add two things here
1. Use the water you have removed when doing a water change as the cleaning medium, not new saltwater.
2. Get some different colored bioballs. Then if you have a variety of colors you can clean one color this time, the other color the next and so on.
1. Use the water you have removed when doing a water change as the cleaning medium, not new saltwater.
2. Get some different colored bioballs. Then if you have a variety of colors you can clean one color this time, the other color the next and so on.
ivasawajin
Member
thanks , can i add a bacteria supp after each time i clean a part ?